Whirlpool WTW8000D Error Codes: Full List & Meanings

The Whirlpool WTW8000D display can show 12 distinct fault codes. 9 of them are things you can check yourself in a few minutes; 3 require a technician because they report an internal board or sensor failure.

Read this first: a code tells you what the machine detected, not what part to buy. Clear the code once, retry one cycle, and only then start diagnosing. Before opening any panel, unplug the washer and shut off the water.

You can check these yourself

Code	What it means	First thing to check
`F5E2`	The lid lock will not engage.	Open the lid and check for any garment caught at the front edge or under the hinge.
`F5E3`	The lid lock will not release.	Take everything off the top of the washer — baskets, bottles, folded laundry.
`F6E2` F6E3	The user interface panel cannot talk to the main control board.	Unplug the washer, or switch the breaker off.
`F6E3` F6E2	Same communication failure as F6E2 — the UI and main control board are out of sync.	Cut power at the breaker for 5 minutes.
`F8E1` LF	The washer is taking too long to fill.	Turn both hot and cold supply valves fully counter-clockwise.
`F8E6`	The lid was left open.	Close the lid fully and press POWER to clear the display.
`F9E1` dr / drn	The washer is taking too long to drain.	Straighten the drain hose and check it is not pinched behind the washer.
`LF` F8E1	Long Fill.	Open both supply valves all the way.
`dr` drn / F9E1	Drain problem — the washer cannot empty the drum in the time allowed.	Unplug the washer first.

These need a technician

Code	What it means	Why it is not DIY
`F1E1`	The main control board (ACU) reported an internal fault.	The code returns after one power cycle. This is a board-level fault with no user-serviceable part.
`F2E5`	The user interface panel and the main control board do not match.	Always. This code means a part mismatch inside the machine.
`F3E1`	The washer cannot read the water level.	The code returns after one rinse cycle. The pressure sensor path is internal.

How to clear a code

Write the code down before you touch anything — it clears on the next start.
Press POWER once. This usually clears the display and exits the cycle.
For a communication code, unplug the washer or switch the breaker off for a full five minutes. The boards reset on power-up.
Run one short cycle. If the code returns, it is a real fault and not a glitch.
If it returns a second time, stop cycling power and read the code page below.

All codes for the WTW8000D

F1E1 The main control board (ACU) reported an internal fault
F2E5 The user interface panel and the main control board do not match
F3E1 The washer cannot read the water level
F5E2 The lid lock will not engage
F5E3 The lid lock will not release
F6E2 The user interface panel cannot talk to the main control board
F6E3 Same communication failure as F6E2 — the UI and main control board are out of sync
F8E1 The washer is taking too long to fill
F8E6 The lid was left open
F9E1 The washer is taking too long to drain
LF Long Fill
dr Drain problem — the washer cannot empty the drum in the time allowed

Other Whirlpool codes

Codes not on this model can still be useful — the washer platform is shared across several model numbers.

More for the WTW8000D

Where this data comes from

Error code tablehttps://s3.amazonaws.com/sm-backend-production-attachments/owners-manual-W10607424-RevB.pdfchecked 2026-10-26

One source is listed above because it is the only place this page draws from. We publish facts we can point to — no republished manual text, no hosted PDFs, no invented model numbers or error codes.